<?xml version="1.0" encoding="UTF-8"?>
<feed xmlns="http://www.w3.org/2005/Atom" xml:lang="en-gb">
	<link rel="self" type="application/atom+xml" href="https://blueirissoftware.com/forum/app.php/feed/topic/4059" />

	<title>Blue Iris</title>
	<subtitle>Blue Iris User Group</subtitle>
	<link href="https://blueirissoftware.com/forum/index.php" />
	<updated>2024-06-24T06:09:55+00:00</updated>

	<author><name><![CDATA[Blue Iris]]></name></author>
	<id>https://blueirissoftware.com/forum/app.php/feed/topic/4059</id>

		<entry>
		<author><name><![CDATA[TimG]]></name></author>
		<updated>2024-06-24T06:09:55+00:00</updated>

		<published>2024-06-24T06:09:55+00:00</published>
		<id>https://blueirissoftware.com/forum/viewtopic.php?p=18317#p18317</id>
		<link href="https://blueirissoftware.com/forum/viewtopic.php?p=18317#p18317"/>
		<title type="html"><![CDATA[Re: Seeking Advice: Configuring Blue Iris to Detect Smoke Alarm Sounds]]></title>

		
		<content type="html" xml:base="https://blueirissoftware.com/forum/viewtopic.php?p=18317#p18317"><![CDATA[
I haven't tried the new audio triggers, but it is clear a lot of work has been done to make this a possibility. If the info available in the Help file isn't enough, then it will need an email to Support and a lot of experimentation.<p>Statistics: Posted by <a href="https://blueirissoftware.com/forum/memberlist.php?mode=viewprofile&amp;u=178">TimG</a> — Mon Jun 24, 2024 6:09 am</p><hr />
]]></content>
	</entry>
		<entry>
		<author><name><![CDATA[Pogo]]></name></author>
		<updated>2024-06-22T20:14:38+00:00</updated>

		<published>2024-06-22T20:14:38+00:00</published>
		<id>https://blueirissoftware.com/forum/viewtopic.php?p=18292#p18292</id>
		<link href="https://blueirissoftware.com/forum/viewtopic.php?p=18292#p18292"/>
		<title type="html"><![CDATA[Re: Seeking Advice: Configuring Blue Iris to Detect Smoke Alarm Sounds]]></title>

		
		<content type="html" xml:base="https://blueirissoftware.com/forum/viewtopic.php?p=18292#p18292"><![CDATA[
Setting up audio triggers for BI is not uncommon. As with evrything Blue Iris, you can make it as simple or as difficult as you want.<br><br>If your intent is to implement a fire alarm going off as an audio trigger for a Blue Iris alert in the event of smoke or fire detection, just use a small ONVIF camera with audio out and there's your BI trigger source.  But it still needs to be conveyed to an end point, presumably a remote one requiring push, email, whatever....<br><br>On the other hand, the TP-Link Tapo C110 Swiss Army Knife of simple and effective solutions comes to mind for 20 bucks..., which after all is basically a baby monitor and could also work just as well (or possibly better) than BI for the purpose intended here via its own more than capable app.<br><br>Plug it in. Done.<p>Statistics: Posted by <a href="https://blueirissoftware.com/forum/memberlist.php?mode=viewprofile&amp;u=5668">Pogo</a> — Sat Jun 22, 2024 8:14 pm</p><hr />
]]></content>
	</entry>
		<entry>
		<author><name><![CDATA[Sardon]]></name></author>
		<updated>2024-06-22T16:01:43+00:00</updated>

		<published>2024-06-22T16:01:43+00:00</published>
		<id>https://blueirissoftware.com/forum/viewtopic.php?p=18290#p18290</id>
		<link href="https://blueirissoftware.com/forum/viewtopic.php?p=18290#p18290"/>
		<title type="html"><![CDATA[Seeking Advice: Configuring Blue Iris to Detect Smoke Alarm Sounds]]></title>

		
		<content type="html" xml:base="https://blueirissoftware.com/forum/viewtopic.php?p=18290#p18290"><![CDATA[
Hi everyone,<br><br>Is it possible to setup an audio event in Blue Iris that would trigger when say a smoke detector goes off? I've read through the manual and noticed there's a mention of audio triggers and states the following on page 66:<br><br> "Here a signal generator was used to provide a proper frequency over the required 2.0 seconds in order to trigger. You may use this to recognize your doorbell, phone ringer, fire or other home alarms"<br><br>So I'm assuming it can be done but I'm not entirely sure how to implement this specific use case.<br><br>Has anyone successfully set up Blue Iris to detect and alert based on a smoke alarm sound? If so, could you share your approach or any tips?<br><br>Any guidance would be greatly appreciated. Thanks in advance!<br>SN<p>Statistics: Posted by <a href="https://blueirissoftware.com/forum/memberlist.php?mode=viewprofile&amp;u=6495">Sardon</a> — Sat Jun 22, 2024 4:01 pm</p><hr />
]]></content>
	</entry>
	</feed>
